布防版权符号怎么输入

测试报告"XXXXX测试报告""测试结果""测试概述",,,,,,"风险列表",,,,,"项目信息""项目名称",,,,"项目经理",,,,,"测试人",,"开始时间",,,,"结束时间",,,,,"测试轮次",,"测试环境""PID",,,,"Device_ID",,,,,"通讯方式",,"固件KEY",,,,"固件/MCU版本",,,,,"基线/协议",,"网关PID",,,,"网关KEY",,,,,"网关版本",,"UIID",,,,"APP版本",,,,,"区域",,"测试模组",,,,"测试手机",,,,,"路由器",,通用功能"通用功能_测试用例""用例编号","子模块","子功能","测试项","测试优先级","标签","前置条件","测试步骤","预期结果","测试结果","实际结果","标识""Alarm_001","通网络管理","配网","选择配网方式","P1",,,"1.
点击"我的家"界面右上角的+号2.
安防传感-传感器-选择配网方式","1.
进入相应的配网界面,界面信息准确",,,"Alarm_002",,,"WiFi快连/指示灯在快闪(WiFi)","P0",,,"1.
选择配网方式:Wi-Fi快连/指示灯在快闪,进行配网2.
触发reset键","1.
配网成功",,,"Alarm_003",,,"热点配网(兼容模式)/指示灯在慢闪(WiFi)","P0",,,"1.
选择配网方式:热点配网(兼容模式)/指示灯在慢闪2.
EZ配网模式下再次触发reset键3.
进入手机热点查找设备生成的AP热点(eg:smartlife_设备id/MAC地址后4位),进行配网","1.
配网成功",,,"Alarm_004",,,"自动发现","P2",,,"1.
选择自动扫描配网,进行配网","1.
自动扫描到待配网设备",,,"Alarm_005",,,"添加失败","P1",,,"1.
查看添加失败页面2.
点击重试","1.
失败提示信息正确2.
点击重试将再次进行添加",,,"Alarm_006",,,"添加成功","P1",,,"1.
查看添加完成界面2.
点击完成","1.
完成界面显示正确",,,"Alarm_007",,"功能退网","APP移除设备","P0",,"已入网","1.
APP"移除设备"后,查看"退网"情况","1.
设备从APP列表移除,断开与APP的通讯",,,"Alarm_008",,,"硬件移除","P1",,,"1.
"触发设备reset键"后,查看"退网情况"效果","1.
设备断开与APP的通讯注:ZigBee设备显示离线,WiFi设备从APP列表移除,NB设备硬件无法移除",,,"Alarm_009",,"再配网","APP解除绑定,再配网","P0",,,"1.
APP"解除绑定"后,再配网,查看APP面板","1.
再配网成功,自定义设备名称和历史记录无丢失",,,"Alarm_010",,,"APP解除绑定并清除数据,再配网","P1",,,"1.
APP"解除绑定并清除数据"后,再配网,查看APP面板","1.
再配网成功,自定义设备名称和历史记录清空",,,"Alarm_011",,,"硬件移除,再配网","P1",,,"1.
"设备重置"后,再配网","1.
再配网成功,自定义设备名称和历史记录无丢失,且已添加的自动化联动正常执行",,,"Alarm_012",,"通用-网络管理-配网成功率","WiFi快连配网成功率-WiFi","P2",,,"1.
APP选择EZ配网方式,进行10次配网,查看配网情况","1.
每次都能配网成功",,,"Alarm_013",,,"热点配网成功率-WiFi","P2",,,"1.
APP选择AP配网方式,进行10次配网,查看配网情况","1.
每次都能配网成功",,,"Alarm_014",,"设备上下线","设备离线","P1",,,"1.
设备断电,查看设备在线状态","1.
面板状态从在线变为离线,不可控,且耗时(ZigBee)>12h,耗时(NB)>24h注:弱电设备:WiFi默认常在线,选配(断电>24h离线);ZigBee断电>12h离线;NB设备断电>24h离线;BLE蓝牙常在线;sigmesh12h常在线强电设备:断电3~5min左右显示离线",,,"Alarm_015",,,"开启离线提醒","P1",,,"1.
离线提醒使能打开2.
将设备断网,查看离线提醒","1.
设备离线30min后可接收到设备的离线提醒",,,"Alarm_016",,,"关闭离线提醒","P1",,,"1离线提醒使能关闭2.
将设备断网超过30分钟,查看是否有离线提醒","1.
没有离线提醒",,,"Alarm_017",,,"设备上线","P1",,,"1.
断电后重新上电,查看设备在线状态","1.
面板显示在线且可控",,,"Alarm_018",,"网络指示灯状态","未配网","P1",,,"1.
设备未配网,查看设备指示灯现象","1.
设备指示灯处于熄灭状态",,,"Alarm_019",,,"配网中","P0",,,"1.
长按设备reset键超过5S,查看指示灯现象","1.
设备指示灯闪烁,闪烁现象符合产品说明书",,,"Alarm_020",,,"配网成功","P1",,"APP进入配网模式","1.
设备配网成功后,查看指示灯显示","1.
指示灯现象符合产品说明书",,,"Alarm_021",,,"配网超时后","P1",,"APP未进入配网模式","1.
长按设备reset键超过5S,查看指示灯现象","1.
指示灯现象符合产品说明书",,,"Alarm_022",,,"APP移除设备后","P1",,,"1.
APP移除设备后,查看指示灯现象","1.
指示灯熄灭,不闪烁",,,"Alarm_023",,,"APP移除设备后触发设备","P1",,,"1.
APP移除设备后,触发设备上报数据或短按设备reset键,查看指示灯现象","1.
指示灯闪烁,设备进入配网模式",,,"Alarm_024",,,"本地移除网络后","P1",,,"1.
长按设备reset键,查看指示灯现象","1.
指示灯闪烁,设备进入配网模式",,,"Alarm_025",,,"移除网络后长按reset键","P1",,,"1.
设备移除网络后长按reset键","1.
指示灯闪烁,进入配网模式",,,"Alarm_026",,,"重上电","P1",,,"1.
设备重新上电后,查看指示灯现象","1.
指示灯常亮约X秒后熄灭",,,"Alarm_027",,,"未配网长按reset键","P1",,,"1.
长按reset键X秒,查看指示灯现象","1.
网络指示灯闪烁,进入配网模式",,,"Alarm_028",,,"配网中短按reset键","P1",,,"1.
设备配网过程中,短按reset键,查看指示灯现象","1.
网络指示灯不会中断闪烁,闪烁时长不会延长",,,"Alarm_029",,,"配网中长按reset键","P1",,,"1.
设备配网过程中,长按reset键,查看指示灯现象","1.
网络指示灯不会中断闪烁,闪烁时长不会延长",,,"Alarm_030","网参配网(WiFi)","SSID","SSID组合","P2",,"SSID组合="字母+数字+符号"","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_031",,,"SSID长度","P2",,"SSID长度="1或10或32"字符","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_032",,"KEY","KEY组合","P2",,"KEY组合="字母+数字+符号(重点空格)"","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_033",,,"KEY长度","P2",,"KEY长度="8或63"字符","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_034",,"安全模式","OPEN","P2",,"密钥类型=OPEN","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_035",,,"WPA-PSK/WPA2-PSK","P2",,"密钥类型=WPA-PSK/WPA2-PSK","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_036",,"密钥模式","AE秒","P2",,"密钥模式=AES","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_037",,,"TKIP","P2",,"密钥模式=TKIP","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_038",,,"TKIP&AES","P2",,"密钥模式=TKIP&AES","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_039",,"频率带宽","自动","P2",,"频率=自动","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_040",,,"20M","P2",,"频率=20M","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_041",,,"40M","P2",,"频率=40M","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_042",,"通用-网参配网(WiFi)-工作模式","11b","P2",,"工作模式=11b","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_043",,,"11g","P2",,"工作模式=11g","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_044",,,"11n","P2",,"工作模式=11n","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_045",,,"11bg","P2",,"工作模式=11bg","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_046",,,"11bgn","P2",,"工作模式=11bgn","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_047",,"工作状态","启用SSID广播","P2",,"工作状态=启用SSID广播","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_048",,,"关闭SSID广播","P2",,"工作状态=关闭SSID广播","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_049",,,"启用无线隔离","P2",,"工作状态=启用无线隔离","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_050",,,"关闭无线隔离","P2",,"工作状态=关闭无线隔离","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_051",,"信道模式","自动信道","P2",,"信道模式=自动","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_052",,,"1~13信道","P2",,"信道模式=1或13","1.
APP选择EZ或AP配网方式,进行配网查看配网情况","1.
配网成功",,,"Alarm_053","电量","电量上报","入网电量","P0",,"首次配网","1.
设备入网后,查看APP端电量显示","1.
显示电量100%/满电/高电量",,,"Alarm_054",,,"断上电","P1",,"更换前后电池电压不一致","1.
更换电池后,查看APP端电量显示","1.
ZigBee设备APP端先显示100%2.
电量20min后显示真实电量3.
WiFi设备APP端显示真实电量",,,"Alarm_055",,,"按键上报","P1",,,"1.
短按设备本地reset键","1.
上报当前电量",,,"Alarm_056",,,"电量周期上报","P1",,,"1.
设备挂机运行24h,查看APP端电量显示","1.
电量大于20%,间隔Xh更新一次当前电量注:免开发ZigBee默认4h上报一次,免开发WiFi默认8h上报一次",,,"Alarm_057",,,"低电量周期上报","P1",,,"1.
设备挂机运行24h,查看APP端电量显示","1.
电量低于20%,间隔Xh更新一次当前电量注:免开发ZigBee默认1h上报一次",,,"Alarm_058",,"电量显示","充电状态","P1",,,"1.
给设备进行外部供电,查看APP端电量显示","1.
APP端显示充电图标2.
电量持续稳定升高",,,"Alarm_059",,,"无动画电量显示","P1",,,"1.
用电量测试仪给设备供不同的电压","1.
电量图标无动画功能,电量百分比根据实际电量发生变化_U2公版面板",,,"Alarm_060",,,"不同电量显示(高,中,低)","P1",,,,"1.
电量低为红色,电量中为橙色,电量高为灰色或绿色",,,"Alarm_061",,,"不同电量显示(0%~100%)","P0",,,,"1.
电量低于20%,电量图标为红色;电量高于20%,电量图标为绿色—U1公版面板",,,"Alarm_062",,"低电量提醒设置","打开低电提醒开关","P1",,"参考配置项,低电可配","1.
IOT平台,PID设置告警<20%;2.
打开低电提醒开关3.
默认WiFi设备供低于2.
36V电压,ZigBee供低于2.
68V电压","1.
APP面板显示电量低于20%或低电量,消息中心推送低电消息",,,"Alarm_063",,,"关闭低电提醒开关","P1",,,"1.
IOT平台,PID设置告警<20%;2.
关闭低电提醒开关3.
默认WiFi设备供低于2.
36V电压,ZigBee供低于2.
68V电压","1.
APP面板显示电量低于20%,消息中心不会推送低电消息注:建议低于20%推送低电消息",,,"Alarm_064","消息中心","消息推送","APP后台运行推送","P1",,,"1.
测试APP和手机消息通知权限已打开2.
使测试APP后台运行触发支持推送的设备消息上报","1.
推送告警消息,且伴随推送音",,,"Alarm_065",,,"APP未运行推送","P1",,,"1.
测试APP和手机消息通知权限已打开2.
使测试APP退出后台运行,触发支持推送的设备消息上报","1.
推送告警消息,且伴随推送音",,,"Alarm_066",,,"APP端设备主面板推送","P1",,,"1.
测试APP和手机消息通知权限已打开2.
进入APP端设备主面板,触发设备消息上报","1.
推送告警消息,且伴随推送音",,,"Alarm_067","基本功能设置","通用-基本功能设置-设备编辑界面","进入设备编辑界面","P1",,,"1.
设备主界面点击右侧的编辑按钮","1.
成功进入设备编辑页面",,,"Alarm_068",,"设备图标更改","进入设备图标编辑界面","P1",,,"1.
点击设备名称右侧的编辑按钮,点击"图标"","1.
显示图标的两钟更改方式",,,"Alarm_069",,,"拍照更改","P1",,,"1.
图标编辑界面,选择拍照,拍取照片并点击完成","1.
设备图标更改为所设置图片",,,"Alarm_070",,,"从手机相册选择更改","P1",,,"1.
图标编辑界面,选择从手机相册,拍取照片并点击完成","1.
设备图标更改为所设置图片",,,"Alarm_071",,"设备名称自定义","进入设备名称更改界面","P1",,,"1.
点击设备名称右侧的编辑按钮,点击"名称"","1.
成功进入设备名称编辑界面",,,"Alarm_072",,,"设备名称=中文","P1",,,"1.
设备名称更改界面,输入汉字点击确定","1.
正确显示自定义设备名称注:设备主界面最多显示14个汉字,其余用"….
"代替",,,"Alarm_073",,,"设备名称=英文","P1",,,"1.
设备名称更改界面,输入汉字点击确定","1.
正确显示自定义设备名称注:设备主界面最多显示29个英文字母,其余用"….
"代替",,,"Alarm_074",,,"设备名称=字符组合","P1",,,"1.
设备名称更改界面,输入汉字,英文,符号,表情图,空格,点击确定","1.
正确显示自定义名称",,,"Alarm_075",,,"设备名称自定义失败","P1",,,"1.
设备名称更改界面,输入超过50个汉字,输点击确定","1.
提示"操作失败,设备名称超出长度限制"",,,"Alarm_076",,"添加设备位置","进入房间管理界面","P1",,,"1.
APP主界面点击".
.
.
",点击房间管理","1.
成功进入房间管理界面",,,"Alarm_077",,,"添加房间","P1",,,"1.
房间管理界面,点击"添加房间",输入房间名称并保存","1.
房间添加成功,显示在房间列表中注:房间名称为空时,提示"请输入房间名称"",,,"Alarm_078",,,"进入位置添加界面","P1",,,"1.
点击设备名称右侧的编辑按钮,点击"位置"","1.
进入位置添加界面,显示所有已添加的房间",,,"Alarm_079",,,"添加设备位置至房间","P1",,,"1.
设备位置添加页面,勾选需添加的房间,点击保存","1.
在相应房间的设备列表可找到该设备",,,"Alarm_080",,"设备信息","设备信息查看","P1",,,"1.
PIR设备编辑页面,点击设备信息","1.
设备虚拟ID和设备时区必须显示",,,"Alarm_081",,"一键执行和自动化","查看一键执行和自动化","P1",,,"1.
PIR设备编辑界面点击"一键执行和自动化"","1.
显示已添加的自动化注:未添加自动化显示"暂无该设备相关的智能"",,,"Alarm_082",,"共享设备(仅WiFi设备、NB设备适合)","共享界面展示","P1",,,"1.
分别使用Android和IOS手机,点击设置功能列表的"共享设备"2.
查看Android和IOS手机界面信息展示","1.
Android和IOS手机界面UI信息展示完整且保持一致",,,"Alarm_083",,,"添加共享界面","P1",,,"1.
分别使用Android和IOS手机,点击界面正下方"共享设备"图标2.
查看添加共享界面","1.
Android和IOS手机界面UI信息展示完整且保持一致",,,"Alarm_084",,,"错误账号共享","P2",,,"1.
添加共享界面,选择与账号相同的所在区域,填写错误的账号2.
查看是否共享成功","1.
共享失败,提示:账号不存在",,,"Alarm_085",,,"不同地区共享","P2",,,"1.
添加共享界面,选择与账号不同的区域A,填写已注册区域A的账号2.
查看是否共享成功","1.
共享失败,提示:不同地区暂时无法分享",,,"Alarm_086",,,"正确共享","P2",,,"1.
添加共享界面,选择与账号相同的所在区域A,填写已注册区域A的账号2.
查看是否共享成功","1.
共享成功,共享列表可查看到该账户",,,"Alarm_087",,,"删除共享账号","P2",,,"1.
设备共享账号列表2.
任意选择某个账号做删除操作","1.
共享账号删除成功",,,"Alarm_088",,"常见问题与反馈","界面展示","P2",,,"1.
点击设置功能列表的"常见问题与反馈"2.
查看Android和IOS手机界面展示","1.
Android和IOS手机界面显示以及功能与公版个人页面的常见问题与反馈保持一致",,,"Alarm_089",,"添加到桌面","添加到桌面","P2",,"IOS机","1.
点击设置功能列表的"添加到桌面"2.
查看手机桌面","1.
手机桌面可查看到设备快捷展示",,,"Alarm_090",,,"快捷跳转","P2",,"IOS机","1.
点击桌面显示的快捷跳转图标","1.
跳转到app的视频预览界面",,,"Alarm_091",,"检查固件升级","固件版本查询","P1",,,"1.
点击设置功能列表的"检查固件升级"","1.
显示当前设备固件版本",,,"Alarm_092",,"移除设备","移除设备提示","P1",,,"1.
点击设置功能列表的"移除设备"图标2.
查看移除提示界面","1.
提示:是否确定移除设备,设备移除后设备相关智能场景均失效",,,"Alarm_093",,,"确认移除设备","P1",,,"1.
确认移除设备,查看设备列表界面","1.
提示:设备移除成功,界面跳转设备列表界面且已无移除设备,设备进入重新配网状态",,,"Alarm_094",,,"取消设备移除","P2",,,"1.
取消设备移除,查看取消后的界面","1.
设备未移除,界面回到设置界面",,,"Alarm_095","共享账号","基本功能","状态同步","P1",,,"1.
触发数据/电量数据上报,查看APP界面显示","1.
界面展示及功能与主账号保持一致",,,"Alarm_096",,,"常见问题与反馈","P2",,,"1.
点击设置功能列表的"常见问题与反馈"","1.
Android和IOS手机界面UI信息展示完整且保持一致",,,"Alarm_097",,,"共享账号移除设备提示","P2",,,"1.
移除设备提示","1.
界面展示及功能与主账号保持一致",,,"Alarm_098",,,"确认移除分享","P2",,,"1.
确认移除分享,查看设备列表界面展示","1.
设备移除,界面跳转回设备列表界面,共享设备从列表重移除",,,"Alarm_099",,,"取消分享移除","P2",,,"1.
取消分享移除,查看界面展示","1.
界面返回设置界面",,,"Alarm_100","历史记录","历史记录显示","历史记录更新","P0",,,"1.
将设备置于不同环境下或触发设备数据上报,拆卸设备外壳,查看历史记录显示","1.
设备主面板,会自动刷新历史记录",,,"Alarm_101",,,"最新历史记录","P1",,,,"1.
最新历史记录与设备当前状态一致",,,"Alarm_102",,,"历史记录内容","P1",,,,"1.
显示设备告警记录和记录发生的时间和日期注:目前设备有防拆功能DP才显示,无防拆DP,历史记录无任何记录",,,"Alarm_103",,,"历史记录时间","P1",,,,"1.
历史记录时间与数据上报时间一致",,,"Alarm_104",,,"历史记录条数","P1",,,,"1.
最多可显示历史记录1000条",,,"Alarm_105",,,"历史记录周期","P1",,,,"1.
历史记录不超过1000条,最多可显示7天的历史记录",,,告警主机"智慧安防-告警主机_测试用例""用例编号","子模块","子功能","测试项","测试优先级","标签","前置条件","测试步骤","预期结果","测试结果","缺陷级","实际结果","标识""Alarm_001","参数配置-报警管理","告警声开关","告警声=开启","P0",,"已入网","1.
APP成功设置主机告警声="开启",查看主机告警声情况","1.
关联的子设备发生告警时,主机有告警音",,,,,,"Alarm_002",,,"告警声=关闭","P0",,"已入网","1.
APP成功设置主机告警声="关闭",查看主机告警声情况","1.
关联的子设备发生告警时,主机无告警音",,,,,,"Alarm_003",,"报警时长","时长=min(1min)","P0",,"已入网","1.
APP端主机主页面点击设置,报警时长选择1min,点击确认2.
触发主机报警,观察实际报警时长","1.
报警时长设置成功,主机报警1min后不再发出报警声,且报警指示灯停止闪烁",,,,,,"Alarm_004",,,"时长=mid(30min)","P1",,"已入网","1.
APP端主机主页面点击设置,报警时长选择30min,点击确认2.
触发主机报警,观察实际报警时长","1.
报警时长设置成功,主机报警30min后不再发出报警声,且报警指示灯停止闪烁",,,,,,"Alarm_005",,,"时长=max(60min)","P1",,"已入网","1.
APP端主机主页面点击设置,报警时长选择60min,点击确认2.
触发主机报警,观察实际报警时长","1.
报警时长设置成功,主机报警60min后不再发出报警声,且报警指示灯停止闪烁",,,,,,"Alarm_006",,"报警音量","音量-静音","P1",,"已入网","1.
APP端主机主页面点击设置,报警音量选择静音,点击确认2.
触发主机报警,观察实际报警音量","1.
报警音量设置成功,主机报警指示灯闪烁但不会发出报警声",,,,,,"Alarm_007",,,"音量-低(1)","P0",,"已入网","1.
APP端主机主页面点击设置,报警音量选择低(1),点击确认2.
触发主机报警,观察实际报警音量","1.
报警音量设置成功,主机报警指示灯闪烁,报警音量较低",,,,,,"Alarm_008",,,"音量-高(7)","P1",,"已入网","1.
APP端主机主页面点击设置,报警音量选择高(7),点击确认2.
触发主机报警,观察实际报警音量","1.
报警音量设置成功,主机报警指示灯闪烁,报警音量较高",,,,,,"Alarm_009",,,"音量-中(2/3/4/5/6)","P1",,"已入网","1.
APP端主机主页面点击设置,报警音量选择中(2/3/4/5/6),点击确认2.
触发主机报警,观察实际报警音量","1.
报警音量设置成功,主机报警指示灯闪烁,报警音量高于低音量,低于高音量",,,,,,"Alarm_010",,"主机音量","音量=静音","P1",,"已入网","1.
APP端主机主页面点击设置,主机音量选择静音,点击确认2.
主机本地进行按键操作,观察主机按键音和语音音量","1.
主机音量设置成功,无任何按键音和语音提示",,,,,,"Alarm_011",,,"音量=低(1)","P0",,"已入网","1.
APP端主机主页面点击设置,主机音量选择低(1),点击确认2.
主机本地进行按键操作,观察主机按键音和语音音量","1.
主机音量设置成功,主机按键音和语音提示音量较低",,,,,,"Alarm_012",,,"音量=高(7)","P1",,"已入网","1.
APP端主机主页面点击设置,主机音量选择高(7),点击确认2.
主机本地进行按键操作,观察主机按键音和语音音量","1.
主机音量设置成功,主机按键音和语音提示音量较高",,,,,,"Alarm_013",,,"音量=中(2/3/4/5/6)","P1",,"已入网","1.
APP端主机主页面点击设置,主机音量选择中(2/3/4/5/6),点击确认2.
主机本地进行按键操作,观察主机按键音和语音音量","1.
主机音量设置成功,主机按键音和语音提示音量高于低音量低于高音量",,,,,,"Alarm_014","参数配置-通讯","设置密码","取消设置","P1",,"已入网","1.
APP端主机主页面点击设置,点击设置密码2.
输入正确的旧密码后,输入6位数字,点击取消","1.
密码设置弹框小时,返回至设置页面",,,,"Alarm_015",,,"输入正确旧密码","P1",,"已入网","1.
APP端主机主页面点击设置,点击设置密码2.
输入正确的旧密码,点击确认","1.
主动弹出新密码输入框",,,,"Alarm_016",,,"输入错误旧密码","P1",,"已入网","1.
APP端主机主页面点击设置,点击设置密码2.
输入错误的旧密码,点击确认","1.
弹框提示"密码错误"",,,,"Alarm_017",,,"输入格式正确新密码","P0",,"已输入正确的旧密码","1.
新密码输入框输入6位数字,点击确认2.
主机本地输入新密码","1.
弹框提示密码设置成功,主机本地输入新密码后,语音提示正确",,,,"Alarm_018",,,"输入与旧密码一致的新密码","P1",,"已输入正确的旧密码","1.
新密码输入框输入旧密码,点击确认","1.
弹框提示密码设置成功,主机本地输入新密码后,语音提示正确",,,,"Alarm_019",,,"输入符号","P1",,"已输入正确的旧密码","1.
新密码输入框输入符号,点击确认","1.
弹框提示请输入6位数字密码",,,,"Alarm_020",,,"输入数字不足6位","P1",,"已输入正确的旧密码","1.
新密码输入框输入数字不足6位,点击确认","1.
弹框提示请输入6位数字密码",,,,"Alarm_021",,,"输入数字超过6位","P1",,"已输入正确的旧密码","1.
新密码输入框输入数字超过6位,点击确认","1.
弹框提示密码设置失败",,,,"Alarm_022","参数配置-其它","主机语言","中文","P0",,"已入网","1.
APP端主机主页面点击设置,主机语言选择中文,点击确认2.
主机本地进行按键操作","1.
主机本地发出中文语音提示",,,,"Alarm_023",,,"English","P1",,"已入网","1.
APP端主机主页面点击设置,主机语言选择英文,点击确认2.
主机本地进行按键操作","1.
主机本地发出英文语音提示",,,,"Alarm_024",,,"Deutsch","P1",,"已入网","1.
APP端主机主页面点击设置,主机语言选择德文,点击确认2.
主机本地进行按键操作","1.
主机本地发出德文语音提示",,,,"Alarm_025",,,"Italiano","P1",,"已入网","1.
APP端主机主页面点击设置,主机语言选择意大利文,点击确认2.
主机本地进行按键操作","1.
主机本地发出意大利文语音提示",,,,"Alarm_026",,,"pyccknЙ","P1",,"已入网","1.
APP端主机主页面点击设置,主机语言选择俄文,点击确认2.
主机本地进行按键操作","1.
主机本地发出俄文语音提示",,,,"Alarm_027",,,"Espanol","P1",,"已入网","1.
APP端主机主页面点击设置,主机语言选择西班牙文,点击确认2.
主机本地进行按键操作","1.
主机本地发出西班牙文语音提示",,,,"Alarm_028",,,"日本语","P1",,"已入网","1.
APP端主机主页面点击设置,主机语言选择日文,点击确认2.
主机本地进行按键操作","1.
主机本地发出日文语音提示",,,,"Alarm_029",,,"Portuguese","P1",,"已入网","1.
APP端主机主页面点击设置,主机语言选择葡萄牙文,点击确认2.
主机本地进行按键操作","1.
主机本地发出葡萄牙文语音提示",,,,"Alarm_030",,"恢复出厂","主机页面恢复出厂","P1",,"已入网","1.
APP端主机主页面点击设置,点击恢复出厂,点击确认","1.
主机的所有设置恢复默认(报警时长,报警音量,主机音量,密码)",,,,"Alarm_031","子设备管理-添加","快速搜索","快添遥控器","P0",,"已入网","1.
APP端主机主页面点击设备,点击快速搜索2.
按下所需添加的遥控器任一按钮","1.
遥控器子设备添加成功,显示在设备列表",,,,"Alarm_032",,,"快添PIR","P0",,"已入网","1.
APP端主机主页面点击设备,点击快速搜索2.
触发PIR上报有人数据","1.
PIR子设备添加成功,显示在设备列表",,,,"Alarm_033",,,"快添门磁","P0",,"已入网","1.
APP端主机主页面点击设备,点击快速搜索2.
打开或关闭门磁","1.
门磁子设备添加成功,显示在设备列表",,,,"Alarm_034",,"添加新设备","触发reset键添加遥控器","P1",,"已入网","1.
APP端主机主页面点击设备,点击添加新设备,选择传感器2.
触发遥控器reset键使遥控器进入配网模式","1.
遥控器子设备添加成功,显示在设备列表",,,,"Alarm_035",,,"触发reset键添加PIR","P1",,"已入网","1.
APP端主机主页面点击设备,点击添加新设备,选择传感器2.
触发PIRreset键使PIR进入配网模式","1.
PIR子设备添加成功,显示在设备列表",,,,"Alarm_036",,,"触发reset键添加门磁","P1",,"已入网","1.
APP端主机主页面点击设备,点击添加新设备,选择传感器2.
触发门磁reset键使PIR进入配网模式","1.
门磁子设备添加成功,显示在设备列表",,,,"Alarm_037","子设备管理-删除","APP解除绑定","解绑遥控器","P1",,"已入网","1.
遥控器页面,点击移除设备,选择解除绑定","1.
遥控器从APP设备列表移除",,,,"Alarm_038",,,"解绑门磁","P1",,"已入网","1.
门磁页面,点击移除设备,选择解除绑定","1.
门磁从APP设备列表移除",,,,"Alarm_039",,,"解绑PIR","P1",,"已入网","1.
PIR页面,点击移除设备,选择解除绑定","1.
PIR从APP设备列表移除",,,,"Alarm_040",,"APP解除绑定并清除数据","解绑遥控器","P1",,"已入网","1.
遥控器页面,点击移除设备,选择解除绑定并清除数据","1.
遥控器从APP设备列表移除",,,,"Alarm_041",,,"解绑门磁","P1",,"已入网","1.
门磁页面,点击移除设备,选择解除绑定并清除数据","1.
门磁从APP设备列表移除",,,,"Alarm_042",,,"解绑PIR","P1",,"已入网","1.
PIR页面,点击移除设备,选择解除绑定并清除数据","1.
PIR从APP设备列表移除",,,,"Alarm_043","防护模式切换","APP页面切换","布防","P0",,"主机已入网,在线","1.
APP端布防页面点击布防按钮","1.
APP端布防按钮橙色显示,且主机本地语音提示布防",,,,,"Alarm_044",,,"门磁打开布防","P1",,"门磁已设置为监控布防的传感器","1.
APP端布防页面点击布防按钮2.
忽略设备页面点击布防","1.
APP端布防按钮被橙色显示,且主机本地语音提示布防注:开合门磁,主机不会报警",,,,,"Alarm_045",,,"主机正常状态撤防","P1",,"主机防护模式不为撤防","1.
APP端布防页面点击撤防按钮","1.
APP端撤防按钮蓝色显示,且主机本地语音提示撤防",,,,,"Alarm_046",,,"主机报警状态撤防","P1",,"主机防护模式不为撤防","1.
APP端告警页面点击撤防按钮","1.
主动返回至布防页面,且APP端撤防按钮蓝色显示,且主机本地语音提示撤防",,,,,"Alarm_047",,,"在家","P0",,"主机已入网,在线","1.
APP端布防页面点击布防按钮","1.
APP端在家按钮绿色显示,且主机本地语音提示留守布防",,,,,"Alarm_048",,,"门磁打开在家","P1",,"门磁已设置为监控在家的传感器","1.
APP端布防页面点击布防按钮2.
忽略设备页面点击布防","1.
APP端在家按钮绿色显示,且主机本地语音提示留守布防注:开合门磁,主机不会报警",,,,,"Alarm_049",,"遥控器切换","布防","P0",,"主机已入网,在线","1.
按下遥控器本地布防按钮","1.
APP端布防按钮橙色显示,且主机本地语音提示布防",,,,,"Alarm_050",,,"门磁打开布防","P1",,"门磁已设置为监控布防的传感器","1.
按下遥控器本地布防按钮","1.
APP端无任何提示,直接切换为布防模式注:开合门磁,主机不会报警",,,,,"Alarm_051",,,"主机正常状态撤防","P1",,"主机防护模式不为撤防","1.
按下遥控器本地撤防按钮","1.
APP端撤防按钮蓝色显示,且主机本地语音提示撤防",,,,,"Alarm_052",,,"主机报警状态撤防","P1",,"主机防护模式不为撤防","1.
按下遥控器本地撤防按钮","1.
主动返回至布防页面,且APP端撤防按钮蓝色显示,且主机本地语音提示撤防",,,,,"Alarm_053",,,"在家","P0",,"主机已入网,在线","1.
按下遥控器本地在家按钮","1.
APP端在家按钮绿色显示,且主机本地语音提示布防",,,,,"Alarm_054",,,"门磁打开在家","P1",,"门磁已设置为监控在家的传感器","1.
按下遥控器本地在家按钮","1.
在家按钮绿色显示,且主机本地语音提示留守布防注:开合门磁,主机不会报警",,,,,"Alarm_055",,"定时切换","定时撤防","P0",,"主机防护模式不为撤防","1.
预设"撤防"定时模式任务,查看防护模式切换情况","1.
APP与设备端均撤防",,,,,"Alarm_056",,,"定时布防","P1",,"主机防护模式不为布防","1.
预设"布防"定时模式任务,查看防护模式切换情况","1.
APP与设备端均布防",,,,,"Alarm_057",,,"定时在家","P1",,"主机防护模式不为在家","1.
预设"在家"定时模式任务,查看防护模式切换情况","1.
APP与设备端均在家",,,,,"Alarm_058","报警","APP求救","取消求救","P1",,"主机处于求救状态","1.
报警页面,点击下方的"取消报警"按钮","1.
APP端返回至主页面(布防页面),主机本地不再发出报警声且报警指示灯停止闪烁",,,,,"Alarm_059",,,"发起求救","P0",,"已入网","1.
APP端布防页面点击右上方报警按钮,长按求救按钮3S","1.
主机本地发出报警声且报警指示灯闪烁,APP端跳转至报警页面,显示紧急报警",,,,,"Alarm_060",,,"求救静音","P1",,"主机处于求救状态","1.
报警页面,点击右上方的音量按钮","1.
音量按钮静音显示,主机本地不再发出报警声,但报警指示灯持续闪烁",,,,,"Alarm_061",,,"取消求救静音","P1",,"主机处于求救静音状态","1.
报警页面,点击右上方的静音按钮","1.
音量按钮正常显示,主机本地再次发出报警声,报警指示灯持续闪烁",,,,,"Alarm_062",,"APP紧急","取消紧急","P1",,"主机处于紧急状态","1.
报警页面,点击下方的"取消报警"按钮","1.
APP端返回至主页面(布防页面),主机本地不再发出报警声且报警指示灯停止闪烁",,,,,"Alarm_063",,,"发起紧急","P0",,"已入网","1.
APP端布防页面点击右上方报警按钮,长按紧急按钮3S","1.
主机本地发出报警声且报警指示灯闪烁,APP端跳转至报警页面,显示紧急报警",,,,,"Alarm_064",,,"紧急静音","P1",,"主机处于紧急状态","1.
报警页面,点击右上方的音量按钮","1.
音量按钮静音显示,主机本地不再发出报警声,但报警指示灯持续闪烁",,,,,"Alarm_065",,,"取消紧急静音","P1",,"主机处于紧急静音状态","1.
报警页面,点击右上方的静音按钮","1.
音量按钮正常显示,主机本地再次发出报警声,报警指示灯持续闪烁",,,,,"Alarm_066",,"APP火警","取消火警","P1",,"主机处于火警状态","1.
报警页面,点击下方的"取消报警"按钮","1.
APP端返回至主页面(布防页面),主机本地不再发出报警声且报警指示灯停止闪烁",,,,,"Alarm_067",,,"发起火警","P0",,"已入网","1.
APP端布防页面点击右上方报警按钮,长按火警按钮3S","1.
主机本地发出报警声且报警指示灯闪烁,APP端跳转至报警页面,显示火灾报警",,,,,"Alarm_068",,,"火警静音","P1",,"主机处于火警状态","1.
报警页面,点击右上方的音量按钮","1.
音量按钮静音显示,主机本地不再发出报警声,但报警指示灯持续闪烁",,,,,"Alarm_069",,,"取消火警静音","P1",,"主机处于火警静音状态","1.
报警页面,点击右上方的静音按钮","1.
音量按钮正常显示,主机本地再次发出报警声,报警指示灯持续闪烁",,,,,"Alarm_070","监控传感器","监控布防传感器","添加门磁","P1",,"主机为撤防模式,门磁为关闭状态","1.
布防页面点击右上方设置按钮,点击安防模式,点击监控传感器下方的布防,勾选门磁,点击保存2.
主机布防后,打开门磁","1.
门磁添加成功2.
主机发出报警声,且报警指示灯闪烁",,,,,"Alarm_071",,,"添加PIR","P1",,"主机为撤防模式,PIR为无人状态","1.
布防页面点击右上方设置按钮,点击安防模式,点击监控传感器下方的布防,勾选PIR,点击保存2.
主机布防后,人员在PIR检测范围内移动","1.
PIR添加成功2.
主机发出报警声,且报警指示灯闪烁",,,,,"Alarm_072",,,"添加遥控器","P1",,"主机为撤防模式","1.
布防页面点击右上方设置按钮,点击安防模式,点击监控传感器下方的布防","1.
遥控器置灰显示,不可勾选",,,,,"Alarm_073",,,"删除门磁","P1",,"主机为撤防模式,门磁为关闭状态","1.
布防页面点击右上方设置按钮,点击安防模式,点击监控传感器下方的布防,取消勾选门磁,点击保存2.
主机布防后,打开门磁","1.
门磁删除成功2.
主机不会报警",,,,,"Alarm_074",,,"删除PIR","P1",,"主机为撤防模式,PIR为无人状态","1.
布防页面点击右上方设置按钮,点击安防模式,点击监控传感器下方的布防,取消勾选PIR,点击保存2.
主机布防后,人员在PIR检测范围内移动","1.
PIR删除成功2.
主机不会报警",,,,,"Alarm_075",,,"布防模式下添加","P1",,"已入网","1.
主机布防后,点击设置,点击安防模式,点击布防","1.
弹框提示"设置模式前,您需要先切换成撤防模式"",,,,,"Alarm_076",,,"布防模式下取消添加","P1",,"已入网","1.
主机布防后,点击设置,点击安防模式,点击布防2.
点击弹框的取消按钮","1.
停留在布防监控传感器添加页面,保存按钮置灰",,,,,"Alarm_077",,,"布防模式下去首页","P1",,"已入网","1.
主机布防后,点击设置,点击安防模式,点击布防2.
点击弹框的去首页按钮","1.
页面返回至首页(布防页面)",,,,,"Alarm_078",,,"在家模式下添加","P1",,"已入网","1.
主机在家后,点击设置,点击安防模式,点击布防","1.
弹框提示"设置模式前,您需要先切换成撤防模式"",,,,,"Alarm_079",,,"在家模式下取消添加","P1",,"已入网","1.
主机在家后,点击设置,点击安防模式,点击布防2.
点击弹框的取消按钮","1.
停留在布防监控传感器添加页面,保存按钮置灰",,,,,"Alarm_080",,,"在家模式下去首页","P1",,"已入网","1.
主机在家后,点击设置,点击安防模式,点击布防2.
点击弹框的去首页按钮","1.
页面返回至首页(布防页面)",,,,,"Alarm_081",,"监控在家传感器","添加门磁","P1",,"主机为撤防模式,门磁为关闭状态","1.
布防页面点击右上方设置按钮,点击安防模式,点击监控传感器下方的在家,勾选门磁,点击保存2.
主机在家后,打开门磁","1.
门磁添加成功2.
主机发出报警声,且报警指示灯闪烁",,,,,"Alarm_082",,,"添加PIR","P1",,"主机为撤防模式,PIR为无人状态","1.
布防页面点击右上方设置按钮,点击安防模式,点击监控传感器下方的在家,勾选PIR,点击保存2.
主机在家后,人员在PIR检测范围内移动","1.
PIR添加成功2.
主机发出报警声,且报警指示灯闪烁",,,,,"Alarm_083",,,"添加遥控器","P1",,"主机为撤防模式","1.
布防页面点击右上方设置按钮,点击安防模式,点击监控传感器下方的在家","1.
遥控器置灰显示,不可勾选",,,,,"Alarm_084",,,"删除门磁","P1",,"主机为撤防模式,门磁为关闭状态","1.
布防页面点击右上方设置按钮,点击安防模式,点击监控传感器下方的在家,取消勾选门磁,点击保存2.
主机在家后,打开门磁","1.
门磁删除成功2.
主机不会报警",,,,,"Alarm_085",,,"删除PIR","P1",,"主机为撤防模式,PIR为无人状态","1.
布防页面点击右上方设置按钮,点击安防模式,点击监控传感器下方的在家,取消勾选PIR,点击保存2.
主机在家后,人员在PIR检测范围内移动","1.
PIR删除成功2.
主机不会报警",,,,,"Alarm_086",,,"布防模式下添加","P1",,"已入网","1.
主机布防后,点击设置,点击安防模式,点击在家","1.
弹框提示"设置模式前,您需要先切换成撤防模式"",,,,,"Alarm_087",,,"布防模式下取消添加","P1",,"已入网","1.
主机布防后,点击设置,点击安防模式,点击在家2.
点击弹框的取消按钮","1.
停留在在家监控传感器添加页面,保存按钮置灰",,,,,"Alarm_088",,,"布防模式下去首页","P1",,"已入网","1.
主机布防后,点击设置,点击安防模式,点击在家2.
点击弹框的去首页按钮","1.
页面返回至首页(布防页面)",,,,,"Alarm_089",,,"在家模式下添加","P1",,"已入网","1.
主机在家后,点击设置,点击安防模式,点击在家","1.
弹框提示"设置模式前,您需要先切换成撤防模式"",,,,,"Alarm_090",,,"在家模式下取消添加","P1",,"已入网","1.
主机在家后,点击设置,点击安防模式,点击在家2.
点击弹框的取消按钮","1.
停留在在家监控传感器添加页面,保存按钮置灰",,,,,"Alarm_091",,,"在家模式下去首页","P1",,"已入网","1.
主机在家后,点击设置,点击安防模式,点击在家2.
点击弹框的去首页按钮","1.
页面返回至首页(布防页面)",,,,,"Alarm_092","延迟报警","布防延迟报警时长","时长=0S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击布防,延迟布防与报警下,点击延迟报警,选择延迟时间为0S,并确定","1.
延迟报警时长设置成功",,,,,"Alarm_093",,,"时长=30S","P0",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击布防,延迟布防与报警下,点击延迟报警,选择延迟时间为30S,并确定","1.
延迟报警时长设置成功",,,,,"Alarm_094",,,"时长=180S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击布防,延迟布防与报警下,点击延迟报警,选择延迟时间为180S,并确定","1.
延迟报警时长设置成功",,,,,"Alarm_095",,,"时长=120S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击布防,延迟布防与报警下,点击延迟报警,选择延迟时间为120S,并确定","1.
延迟报警时长设置成功",,,,,"Alarm_096",,"在家延迟报警时长","时长=0S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击在家,延迟布防与报警下,点击延迟报警,选择延迟时间为0S,并确定","1.
延迟报警时长设置成功",,,,,"Alarm_097",,,"时长=30S","P0",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击在家,延迟布防与报警下,点击延迟报警,选择延迟时间为30S,并确定","1.
延迟报警时长设置成功",,,,,"Alarm_098",,,"时长=180S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击在家,延迟布防与报警下,点击延迟报警,选择延迟时间为180S,并确定","1.
延迟报警时长设置成功",,,,,"Alarm_099",,,"时长=120S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击在家,延迟布防与报警下,点击延迟报警,选择延迟时间为120S,并确定","1.
延迟报警时长设置成功",,,,,"Alarm_100",,"延迟报警","布防延迟报警","P1",,"主机布防模式,且门磁监控布防模式","1.
打开门磁","1.
APP端布防的红色倒计时进度条缩短,时长=延迟报警声时长,倒计时结束后APP端跳转至报警页面显示盗窃报警,同时主机本地发出报警声且报警声指示灯闪烁",,,,,"Alarm_101",,,"在家延迟报警","P1",,"主机在家模式,且门磁监控在家模式","1.
打开门磁","1.
APP端在家的红色倒计时进度条缩短,时长=延迟报警声时长,倒计时结束后APP端跳转至报警页面显示盗窃报警,同时主机本地发出报警声且报警声指示灯闪烁",,,,,"Alarm_102","延迟布防","在家延迟布防","时长=0S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击在家,延迟布防与报警下,点击延迟布防,选择延迟时间为0S,并确定","1.
延迟布防时长设置成功",,,,,"Alarm_103",,,"时长=30S","P0",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击在家,延迟布防与报警下,点击延迟布防,选择延迟时间为30S,并确定","1.
延迟布防时长设置成功",,,,,"Alarm_104",,,"时长=180S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击在家,延迟布防与报警下,点击延迟布防,选择延迟时间为180S,并确定","1.
延迟布防时长设置成功",,,,,"Alarm_105",,,"时长=120S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击在家,延迟布防与报警下,点击延迟布防,选择延迟时间为120S,并确定","1.
延迟布防时长设置成功",,,,,"Alarm_106",,,"APP端在家延迟布防","P1",,"在家的延迟布防时间不为0","1.
APP端布防页面点击在家按钮","1.
APP端在家按钮绿色显示,倒计时进度条逐渐缩短,且APP端布防页面上方滚动显示当前倒计时时间,主机本地发出"嘀"的倒计时音,倒计时结束后主机本地语音提示"留守布防",倒计时时长=设置的在家延迟布防时长",,,,,"Alarm_107",,,"遥控器在家延迟布防","P1",,"在家的延迟布防时间不为0","1.
按下遥控器本地在家按钮","1.
在家按钮绿色显示,倒计时进度条逐渐缩短,且APP端布防页面上方滚动显示当前倒计时时间,主机本地发出"嘀"的倒计时音,倒计时结束后主机本地语音提示"留守布防",倒计时时长=设置的在家延迟布防时长",,,,,"Alarm_108",,"布防延迟布防","时长=0S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击布防,延迟布防与报警下,点击延迟布防,选择延迟时间为0S,并确定","1.
延迟布防时长设置成功",,,,,"Alarm_109",,,"时长=30S","P0",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击布防,延迟布防与报警下,点击延迟布防,选择延迟时间为30S,并确定","1.
延迟布防时长设置成功",,,,,"Alarm_110",,,"时长=180S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击布防,延迟布防与报警下,点击延迟布防,选择延迟时间为180S,并确定","1.
延迟布防时长设置成功",,,,,"Alarm_111",,,"时长=120S","P1",,"主机撤防模式","1.
布防页面点击设置按钮,点击安防模式,点击布防,延迟布防与报警下,点击延迟布防,选择延迟时间为120S,并确定","1.
延迟布防时长设置成功",,,,,"Alarm_112",,,"遥控布防延迟布防","P1",,"布防的延迟布防时间不为0","1.
按下遥控器本地布防按钮","1.
APP端布防按钮橙色显示,倒计时进度条逐渐缩短,且APP端布防页面上方滚动显示当前倒计时时间,主机本地发出"嘀"的倒计时音,倒计时结束后主机本地语音提示"布防",倒计时时长=设置的布防延迟布防时长",,,,,"Alarm_113",,,"APP端布防延迟布防","P1",,"布防的延迟布防时间不为0","1.
APP端布防页面点击布防按钮","1.
APP端布防按钮橙色显示,倒计时进度条逐渐缩短,且APP端布防页面上方滚动显示当前倒计时时间,主机本地发出"嘀"的倒计时音,倒计时结束后主机本地语音提示"布防",倒计时时长=设置的布防延迟布防时长",,,,,"Alarm_114","一键执行","更改布防模式","布防(布防)","P1",,"已入网","1.
添加一键执行,任务为布防(布防)并保存2.
点击所添加的一键执行","1.
一键执行添加成功2.
主机布防布防",,,,,"Alarm_115",,,"在家(布防)","P1",,"已入网","1.
添加一键执行,任务为在家(布防)并保存2.
点击所添加的一键执行","1.
一键执行添加成功2.
主机在家布防",,,,,"Alarm_116",,,"撤防","P1",,"已入网","1.
添加一键执行,任务为撤防并保存2.
点击所添加的一键执行","1.
一键执行添加成功2.
主机撤防",,,,,"Alarm_117",,"操作设备","报警时长","P1",,"已入网","1.
添加一键执行,任务为报警时长(设置时长为X)并保存2.
点击所添加的一键执行","1.
一键执行添加成功2.
主机报警时长更新为X",,,,,"Alarm_118",,,"报警声开关","P1",,"已入网","1.
添加一键执行,任务为报警声开关(开启或关闭)并保存2.
点击所添加的一键执行","1.
一键执行添加成功2.
主机的报警声开关开启或关闭",,,,,"Alarm_119",,,"报警音量","P1",,"已入网","1.
添加一键执行,任务为报警音量(设置音量为X)并保存2.
点击所添加的一键执行","1.
一键执行添加成功2.
主机报警音量更新为X",,,,,"Alarm_120",,,"主机音量","P1",,"已入网","1.
添加一键执行,任务为主机音量(设置音量为X)并保存2.
点击所添加的一键执行","1.
一键执行添加成功2.
主机音量更新为X",,,,,"Alarm_121",,,"主机状态","P1",,"已入网","1.
添加一键执行,任务为主机状态(正常或报警)并保存2.
点击所添加的一键执行","1.
一键执行添加成功2.
主机状态切换为正常或报警",,,,,"Alarm_122",,,"恢复出厂","P1",,"已入网","1.
添加一键执行,任务为恢复出厂(开启)并保存2.
点击所添加的一键执行","1.
一键执行添加成功2.
主机的所有设置恢复为默认(如主机音量,报警音量,报警时长,密码)",,,,,"Alarm_123",,,"主机语言","P1",,"已入网","1.
添加一键执行,任务为主机语言(中文/英文/德文/意大利文/俄文/西班牙文/日语/葡萄牙文)并保存2.
点击所添加的一键执行","1.
一键执行添加成功2.
主机语言切换为相应的语言",,,,,"Alarm_124","智能","自动化","恢复出厂","P1",,"已入网","1.
APP端预设"用例名称"条件,查看联动任务执行情况","1.
条件满足,联动任务执行成功",,,,,"Alarm_125",,,"网关事件推送","P1",,"已入网","1.
APP端预设"用例名称"条件,查看联动任务执行情况","1.
条件满足,联动任务执行成功",,,,,"Alarm_126",,,"报警时长","P1",,"已入网","1.
APP端预设"用例名称"条件,查看联动任务执行情况","1.
条件满足,联动任务执行成功",,,,,"Alarm_127",,,"主机语言","P1",,"已入网","1.
APP端预设"用例名称"条件,查看联动任务执行情况","1.
条件满足,联动任务执行成功",,,,,"Alarm_128",,,"报警声开关","P1",,"已入网","1.
APP端预设"用例名称"条件,查看联动任务执行情况","1.
条件满足,联动任务执行成功",,,,,"Alarm_129",,,"报警音量","P1",,"已入网","1.
APP端预设"用例名称"条件,查看联动任务执行情况","1.
条件满足,联动任务执行成功",,,,,"Alarm_130",,,"主机音量","P1",,"已入网","1.
APP端预设"用例名称"条件,查看联动任务执行情况","1.
条件满足,联动任务执行成功",,,,,"Alarm_131",,,"充电状态","P1",,"已入网","1.
APP端预设"用例名称"条件,查看联动任务执行情况","1.
条件满足,联动任务执行成功",,,,,"Alarm_132",,,"电池电量","P1",,"已入网","1.
APP端预设"用例名称"条件,查看联动任务执行情况","1.
条件满足,联动任务执行成功",,,,,"Alarm_133",,,"主机状态","P1",,"已入网","1.
APP端预设"用例名称"条件,查看联动任务执行情况","1.
条件满足,联动任务执行成功",,,,,缺陷列表"缺陷列表""缺陷单号","缺陷模块","缺陷标题","测试建议","结论(PM)","缺陷状态","缺陷等级","出现概率","解决人(PM/PG)",,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,修订记录"修订记录",,,,,"序号","变更时间","版本","变更人","审批人","变更说明"1,"2020.
5.
23","V1.
0.
0","杨闯","朱春峰","1.
创建"2,"2020.
7.
25","V1.
0.
1","杨闯","朱春峰","1.
更新设备端信息"3,,,,,4,,,,,5,,,,,6,,,,,7,,,,,8,,,,,9,,,,,10,,,,,"涂鸦智能版权所有",,,,,